Welcome to the Free Trade only download
page for our Dream 21N + EOBD Pro kit Software.
WARNING
This download page and software is not
for general public use it is here for the convenient use by FES Autogas Trained
installers only.
********* DO NOT USE OR DOWNLOAD IF YOU ARE NOT A FES AUTOGAS
TRAINIED INSTALLER. ********
Altering the settings on your vehicle with any
of these software downloads without full training by FES Autogas will cause emission
issues and thus possible lead on to major engine damage.
We cannot be held responsible when
you cause damage by using this software or firmware’s.
---------------------------------------------------------------------------------------------------------
Our EOBD kits can be used
on EOBD cars or NON EOBD cars simply by connecting the wire or not. The EOBD feature within our gas ECU physically
controls the gas mixture from the cars own EOBD port and cars fuel trims so you
can be assured of great fuel mixtures because the car is trimming get’s own gas
ECU plus if you have the software key to open the Map screen you can see the
cars EOBD fuel trims.
As well as NEW Permanently lower fixed prices for our injection systems we have some great new software features usually only available on high priced injection kits.
So with FES Autogas and the OMVL / AEB you get Low, Low prices, Reliable components and don't forget, our kits only need 1 reducer which comes in the kit (8 cylinder 400 hp from one reducer)
We
even subsidised the
Next Working day delivery cost on all our goods, plus your orders can be taken
till 4.00 pm every weekday, for next day delivery.
Contact us for your latest price on this system.
This new software has many new features, like -
1) Sequential change over to
gas. This is where each gas injector turns on 1 at a time, so there is no
sense by the owner of the car when going from gas to petrol.
2)
Ability in Diagnostics to switch each gas injector on and off individually and
thus run on petrol or gas, any single injector at any time for diagnostic
purposes.
3)
See each petrol injection point on screen which tells you if you have wired up
to a petrol injector wrong or it is not firing.
4)
Petrol Addition - The ability to add a little bit of petrol in to the gas (gas
/ petrol mix) at high rev's, if you need to wet the valves at all to stop any
valve problems like on some cars. You decide on the amount of petrol to
put in and also when to do it.
5)
Full diagnostics page showing if there is a problem, these faults are logged
till you delete them
6)
Switch back and forth from Petrol to gas at the press of a computer button -
Ideal to compare both petrol & gas injection times together.
7)
Select OMVL or Matrix injectors in the software, depending which ones you have
fitted.
8)
You have the option of emulating the pre or post cats or both at once, if you
have problematic car where the check lights come on.
9)
Full group, Sequential or MJ injection all at the touch of a button.
10)
Counters, to tell you how many hours you have ran on Petrol or Gas
Plus on the New August 2010
version we also have the following New features
· Improved
graphical layout for easier reading
· Wireless
interface: support for ZigBee wireless interface
410777 – yes, there is now a wireless programming lead
· Start on
gas with hot engine: the engine is cranked on gas, if water is
warmer than programmed temperature. Otherwise the engine is cracked on petrol,
and the usual
Automatic
change-over procedure applies.
· Valvetronic
/ Start & Stop: support for BMW Valvetronic engines and
Peugeot engines with Start & Stop feature
· MultiAir:
support for new Fiat MultiAir engines
· Cut-extra
injections: cures extra-injections of some cars, by
completely ignoring short petrol injections.
· Active
diagnosis: new features to test change over switch
and solenoid valves, even with the engine off.
· Wider
12x12 gas map, for more accurate calibration
· Software
change-over switch is always there on screen, for easier
change-over during calibration on the map, you can switch also with the SPACE
BAR, on the keyboard.
· New CNG sensors: support for new AEB807 manometer and
Sensata 260bar high pressure sensor (“piezo” type),
installed in OMVL RP-07, OMCR-08, RP-09 series of
CNG pressure
reducers.
· OBD
connection: you can force a specific protocol, to
fix problems of some cars with many ECUs on the same bus (gas ECU, petrol ECU,
ABS, etc). Default setting “Auto” scans the connection and automatically finds
the correct protocol.
· Automatic
connection: new software continuously polls all
available ports, in search for an ECU. The communication starts automatically.
Supported ECUs – UK specification ones only
· Dream XXI-E 3-4 cylinders ECU
· Dream XXI-N 3-4 cylinders ECU, OBD and previous versions
· Dream XXI-N 5-6-8 cylinders ECU, OBD and previous versions
· Dream XXI-N 10 cylinders ECU
New firmwares
· Dream XXI-E 3-4 cylinders: 12.03
· Dream XXI-N OBD 3-4 cylinders: 10.05
· Dream XXI-N OBD 5-6-8 cylinders: 05.05
Backward compatibility
· New software is compatible with any previous version of Dream XXI-E and
Dream XXI-N ECUs, OBD or non-OBD
· Previously stored configurations can be loaded in the new software,
which supports older 6x12 gas maps
· Configurations, Firmware’s and Acquisitions are now stored into
Documents\OMVL folder.
To access
older files, browse to C:\Program files\OMVL\Dream XXI-N folder.
Note:
new software automatically un-installs previous version of Dream XXI-N
software.
Saved
configurations are preserved into C:\Program files\OMVL\Dream XXI-N folder
*** If you use any software and have not updated the firmware you will
get error 2 connection messages. The fix is simple - choose the latest firmware
for that ecu type and reprogram the firmware to reconnect. For Non EOBD 4 cylinder is firmware version (20) 2000, and 5/6 & 8 is version (30)
3000.
Download the software – all zip files so
unzip and load into your PC.
We always recommend backing up any config
files you have saved before installing any Dream 21N software
******** DO NOT USE OR DOWNLOAD IF YOU ARE NOT
A FES AUTOGAS TRAINIED INSTALLER. ********
We cannot be held responsible when
you cause damage by using this software or firmware’s.
|
Info |
Download |
Date
of issue by FES Autogas |
|
|
|
|
|
Original NON EOBD software. |
2007 |
|
|
Early EOBD Software till August
2010 |
2009 |
|
|
All
singing all dancing Dream 21N EOBD and Earlier software (works on all
versions of Dream 21N ecu’s) – NO Key needed to see map! |
Click here for latest , unlocked
version eobd - 6.0.8 ALWAYS
UPDATE TO THE LATEST FIRMWARE FROM THIS SOFTWARE ON A NEW INSTALLATION!! On installation of software - please go to the manual section of
the software and read the new PDF manual for full functionality uses of new
software features before using it on any vehicles. |
August 2011 |
Information and software can change at
anytime. Even if you’re a Trained FES Autogas
Installer, Please contact us before using any items downloaded from here